Best Dash Cam Settings for the VIOFO A119 V3 QHD Dash Cam

Resolution: 1440P @ 30FPS (default)

For the resolution, our recommended setting is 1440P. Lower resolutions or 60 frames per second significantly reduce detail.

Bitrate: Medium

A high bitrate may improve video quality and smoothness, particularly when recording fast motion or high contrast scenes. The amount of recording time available on your memory card may be reduced if you use high bitrate mode. Using a low bitrate saves space and allows you to record for longer periods of time.

Loop Recording: 3 Minutes

Three minutes strikes a good balance between finding the desired moment and having to scroll through a large number of files.

Video Format: TS

The options are . MP4 and . TS video format. TS format is better to avoid file corruption.

Exposure: 0

You can adjust the EV (Exposure Value) to get better recording results under different lighting conditions. The range is -2.0 to +2.0, and our recommended value is 0.0.

WDR (Wide Dynamic Range): OFF

The dynamic range of an image is defined as the ratio of its brightest to darkest areas. WDR allows the camera to produce video with near-perfect exposure in a variety of lighting conditions.

The A119 V3 gives you three parking mode options:

1. Auto event detection: When a moving object is detected during parking, the camera will automatically record for 1 minute. If there are no new movements, it will stop recording.

2. Time lapse recording: Time-lapse recording captures a video at low frame rates of 1 / 2 / 3 / 5 / 10 / 15 fps, and it records continuously without audio.

3. Low bitrate recording: This mode records video at a low bitrate of 4MB/s for both the front and back cameras. It continuously records in mini le size with audio recorded.

Note: We recommend buying VIOFO HK3 ACC hardwire kit cable for parking mode recording.

Enter Parking Mode Timer: Your Preference

Set the timer for entering parking modes.

Parking Recording Timer:

Set the parking recording duration.

Parking G-sensor: HIGH

When the G-sensor detects significant or sudden movement (such as an impact or collision), an event recording is initiated. In parking mode recording, we recommend setting it to High sensitivity.

Parking Motion Detection: MID

This adjusts the detection sensitivity so that minor motion caused by wind or rain does not trigger a recording.

Time-lapse Recording and Motion Detection: OFF

When this feature is enabled, if there is movement in front of the camera, a recording will begin. When the camera detects no movement for 60 seconds, the recording is stopped and the device switches to detect mode. If the device detects a new movement in front of the camera, it will start recording again.

GPS: ON

If this option is disabled, your camera will no longer measure your speed and position, nor will it synchronize the time/date with the atomic clock. Note that is only available when connected to a GPS signal.

Speed Unit: Your Preference

Sets the speed unit, either in kilometers per hour (KPH) or miles per hour (MPH) (MPH).

G-sensor: LOW

The force required to prevent the file from being overwritten by loop-recording is determined by this setting, which sensor ranges from 'Low' to 'High'.

Date Stamp: ON

Imprints the time and date on your recorded video.

GPS Info Stamp: Your Preference

Imprints the GPS information on the recorded video.

Camera Model Stamp: Your Preference

Imprints the camera model on the recorded video.

Record Audio: ON

This activates or deactivates the microphone. This can also be accessed by holding down the []button while the camera is recording.

Screen Saver: 1 Minute

This turns the screen OFF after a set time.

Boot Delay: 0

When you turn on the camera, it will take a few seconds to boot up. The settings you can choose from are O / 5s / 10s.

LED: ON

This turns the LED light ON / OFF.

Date / Time: Your Preference

System date / time setting

Time Zone: Your Preference

The current time zone is set for GPS time and date calibration. Keep in mind that the time zone must be manually adjusted for daylight savings.

Language: Your Preference

Display language setting (English, Traditional Chinese, French, etc).

Beep Sound: ALL ON

Turns all notification sounds.

Frequency: 60 HZ for USA and Canada

This is the setting for frequency adjustment to reduce flickering and banding in recorded video.

Image Rotation: OFF

Turns the screen upside down.

Format: Once a month

All data on the MicroSD card will be erased during the procedure. Once the Micro SD card is formatted, all information on it is lost and cannot be recovered, so make a backup of all important files.

Format Warning: 30 Days

This sets the number of days between format warnings.

Default Setting: 30 Days

This restores camera settings to factory defaults.

Car Number: Your Preference

This is useful for adding license plates or other identifying features.

Custom Text Stamp: Your Preference

Imprints the customized text on the recorded video.

Firmware Version: Current firmware version check